Welcome

Back to Top

Zoom

Details

Auto ignition probe CX-6

Auto ignition probe HT-25 HT -25 are designed to measure high voltage the output of the ignition coils respectively of the secondary winding or secondary or power output ( for high-voltage diode) . capacitive sensor can be be used to capture high voltage waveforms, both conventional distributor ignition systems and on systems without distributor (DIS ) - the fully electronic ignition systems . For the diagnosis of the secondary coil on plug systems (EFS / COP ) is necessary use extension adapter coil on plug

Use the diagnosis

Given the very high voltage (up to 40kV ) that for secondary circuit typically not possible perform measurements directly connecting the output of the coil, as is the case with measurement of primary. Trying to such measurement could seriously endanger health technology and certainly would lead to the destruction of oscilloscope and computer. to measure Therefore, secondary use capacity and inductive sensor. involvement pliers is simple. First of all involved ground clamp pliers the motor housing , then clipped with pliers Spark cable , or the extension adapter, connector clamp connects the BNC oscilloscope input , start the engine and measure can begin. Pliers features used to measure the ignition on one cylinder , for a test to secondary four-cylinder engine , it is necessary 4 used pliers and possibly 4connection adapters

Examples of use - Ignition systems:

- conventional spark systems (with distributor) 
- CIC (Coil in Cap) as GM HEI, Toyota, Honda, Nippondenso etc.
- DIS (no distributor) fully electronic ignition. With the extension, also EFS / COP

Control Program HANTEK 3064 / A and 1008C are pre-measurement for very precise diagnosis of the secondary. In the preset measurement is integrated into the formula to calculate the values spark voltage (needle) voltage discharge at spark, burning time and duration inductive.

AUTO IGNITION PROBE CX-6.

  • Preis: 31 $ - Auf Lager

Parameters

Garantie 2 Jahre
Model Nein
Parameters

Auto ignition probe CX-6 can be used with most oscilloscopes and motortesters from other manufacturers assuming, that oscilloscope has invert display function and attenuation setting to value 1000:1 or 10000:1.

Do you own a digital oscilloscope and you need help with compatibility of your device with accessories offered by us? Please contact us.

Demonstrations

Videos Nein
Pictures

Support

Manual Nein
Datasheet Nein
Software Nein
Firmware Nein
FAQ Nein

Bewertungen

Sie schreiben ein Review für: AUTO IGNITION PROBE CX-6

Wie bewerten Sie dieses Produkt? *

  1 Stern 2 Sterne 3 Sterne 4 Sterne 5 Sterne
Quality
Price
Value

Produkttags

Verwenden Sie Leerzeichen um Tags zu trennen. Verwenden Sie Apostrophe (') für Phrasen.

New handhelds
Produkte vergleichen (53)
  1. Diesen Gegenstand entfernen

    DSO 1062B

  2. Diesen Gegenstand entfernen

    DSO 1102B

  3. Diesen Gegenstand entfernen

    DSO 1202B

  4. Diesen Gegenstand entfernen

    DSO 1202BV

  5. Diesen Gegenstand entfernen

    DSO 1062BV

  6. Diesen Gegenstand entfernen

    DSO 1102BV

  7. Diesen Gegenstand entfernen

    DSO 1200

  8. Diesen Gegenstand entfernen

    MSO 8060

  9. Diesen Gegenstand entfernen

    CONNECTING DIAGNOSTIC ADAPTER 6 PIN

  10. Diesen Gegenstand entfernen

    AUTOMOTIVE ATTENUATOR 20:1 HANTEK

  11. Diesen Gegenstand entfernen

    CURRENT CLAMP HANTEK CC-65A

  12. Diesen Gegenstand entfernen

    CURRENT CLAMP HANTEK CC-650A

  13. Diesen Gegenstand entfernen

    CURRENT CLAMP Tecpel 60A

  14. Diesen Gegenstand entfernen

    CURRENT CLAMP Tecpel 600A

  15. Diesen Gegenstand entfernen

    CURRENT CLAMP Tecpel 1000A

  16. Diesen Gegenstand entfernen

    AUTO IGNITION PROBE HT-25

  17. Diesen Gegenstand entfernen

    AUTO IGNITION PROBE CX-6

  18. Diesen Gegenstand entfernen

    DSO 2090

  19. Diesen Gegenstand entfernen

    CONTROL LEAD GOLD-SILICONE 2M

  20. Diesen Gegenstand entfernen

    DSO 2150

  21. Diesen Gegenstand entfernen

    DSO 2250

  22. Diesen Gegenstand entfernen

    CONNECTOR – BNC PLUG

  23. Diesen Gegenstand entfernen

    ADAPTER BNC-BANANA 2X4MM

  24. Diesen Gegenstand entfernen

    ADAPTER SAFETY BNC-BANANA 2X4MM

  25. Diesen Gegenstand entfernen

    CONNECTING CLUTCH 4MM

  26. Diesen Gegenstand entfernen

    BNC-BNC 0,45M HANTEK

  27. Diesen Gegenstand entfernen

    CL ADAPTER UPS UNIVERSAL

  28. Diesen Gegenstand entfernen

    DSO 3064

  29. Diesen Gegenstand entfernen

    DSO 3064A

  30. Diesen Gegenstand entfernen

    DSO 3062L

  31. Diesen Gegenstand entfernen

    DSO 3062AL

  32. Diesen Gegenstand entfernen

    DSO 3062A

  33. Diesen Gegenstand entfernen

    DSO 6022BE

  34. Diesen Gegenstand entfernen

    DSO 6052BE

  35. Diesen Gegenstand entfernen

    DSO 6082BE

  36. Diesen Gegenstand entfernen

    DSO 5062B

  37. Diesen Gegenstand entfernen

    DSO 5102B

  38. Diesen Gegenstand entfernen

    DSO 5202B

  39. Diesen Gegenstand entfernen

    DSO 5072P

  40. Diesen Gegenstand entfernen

    DSO 5102P

  41. Diesen Gegenstand entfernen

    DSO 5202P

  42. Diesen Gegenstand entfernen

    MSO 5062D

  43. Diesen Gegenstand entfernen

    MSO 5102D

  44. Diesen Gegenstand entfernen

    MSO 5202D

  45. Diesen Gegenstand entfernen

    DSO 1008C

  46. Diesen Gegenstand entfernen

    MSO 5054F

  47. Diesen Gegenstand entfernen

    PROFISET EXPERT 3064A CZ

  48. Diesen Gegenstand entfernen

    PROFISET PROFESSIONAL 3064A CZ

  49. Diesen Gegenstand entfernen

    PROFISET SIMPLE 1008C

  50. Diesen Gegenstand entfernen

    PROFISET EXTENSIVE 1008C

  51. Diesen Gegenstand entfernen

    1025G HANTEK

  52. Diesen Gegenstand entfernen

    Transport case 1008

  53. Diesen Gegenstand entfernen

    Transport case Handhelds

Alle löschen